Key Commercial Data
Orderkey | 2702663 |
---|---|
Packing unit | 1 pc |
Catalog page | Page 250 (C-6-2019) |
GTIN | 4055626280233 |
Weight per Piece (excluding packing) | 160.000 g |
Custom tariff number | 85364900 |
Country of origin | DE (Germany) |
Note
Utilization restriction | EMC: class A product, see manufacturer’s declaration in the download area |
---|
Ambient conditions
Ambient temperature (operation) | -40 °C … 70 °C (observe derating) |
---|---|
Ambient temperature (storage/transport) | -40 °C … 85 °C |
Max. permissible relative humidity (operation) | 75 % (on average, 85% infrequently, non-condensing) |
Max. permissible humidity (storage/transport) | 75 % (on average, 85% infrequently, non-condensing) |
Maximum altitude | ≤ 2000 m (Above sea level) |
Power supply
Rated control circuit supply voltage US | 24 V DC -20 % / +25 % (A1/A2) |
---|---|
19.2 V DC … 30 V DC | |
Rated control supply current IS | typ. 45 mA |
Power consumption at US | typ. 1.08 W |
Inrush current | typ. 120 mA (Δt <10 ms at Us) |
Filter time | max. 2 ms (at A1-A2 in the event of voltage dips at Us) |
max. 2 ms (at A1-A2; low test pulse width) | |
> 30 ms (at A1-A2; low test pulse rate) | |
max. 2 ms (at A1-A2; high test pulse width) | |
> 1 s (at A1-A2; high test pulse rate) | |
Protective circuit | Serial protection against polarity reversal 35 V suppressor diode (A1-A2) |
Relay outputs: enabling current path
Output name | Enabling current path |
---|---|
Output description | 2 N/O contacts in series, without delay, floating |
Number of outputs | 1 (safety-related N/O contacts: 13/14) |
Contact type | 1 enabling current path |
Contact material | AgSnO2 |
Switching voltage | min. 12 V AC/DC |
max. 250 V AC/DC (Observe the load curve) | |
Limiting continuous current | 6 A (High demand) |
4 A (Low demand) | |
Inrush current | min. 3 mA |
max. 6 A | |
Sq. Total current | 36 A2(observe derating) |
Switching capacity | min. 60 mW |
Switching frequency | max. 1 Hz |
Mechanical service life | 10x 106cycles |
Switching capacity according to IEC 60947-5-1 | 4 A (24 V (DC13)) |
5 A (250 V (AC15)) | |
Output fuse | 6 A gL/gG |
4 A gL/gG (for low-demand applications) |
Relay outputs: return current/signaling current path
Output name | Confirmation current path |
---|---|
Output description | 2 N/C contacts in series, without delay, floating |
Number of outputs | 1 (safety-related N/C contacts: 21/22) |
Contact type | 1 confirmation current path |
Contact material | AgCuNi, + Au |
Switching voltage | min. 5 V DC |
max. 30 V DC | |
Limiting continuous current | 100 mA |
Inrush current | min. 1 mA |
max. 100 mA | |
Switching capacity | min. 20 mW |
Switching frequency | max. 1 Hz |
Mechanical service life | 10x 106cycles |
Output fuse | 150 mA Fast-blow |
Times
Typical pickup time at US | < 70 ms (with Uswhen controlled via A1) |
---|---|
Typical release time at US | < 30 ms (when controlled via A1) |
Recovery time | 500 ms |
General
Relay type | Electromechanical relay with forcibly guided contacts in accordance with IEC/EN 61810-3 (EN 50205) |
---|---|
Nominal operating mode | 100% operating factor |
Net weight | 70.162 g |
Mounting position | vertical or horizontal |
Mounting type | DIN rail mounting |
Assembly instructions | See derating curve |
Degree of protection | IP20 |
Min. degree of protection of inst. location | IP54 |
Housing material | PBT |
Housing color | yellow |
Operating voltage display | 1 x yellow LED |
Status display | 1 x green LED |
Connection data
Connection method | Screw connection |
---|---|
pluggable | no |
Conductor cross section solid min. | 0.2 mm² |
Conductor cross section solid max. | 2.5 mm² |
Conductor cross section flexible min. | 0.2 mm² |
Conductor cross section flexible max. | 2.5 mm² |
Conductor cross section AWG min. | 26 |
Conductor cross section AWG max. | 12 |
Stripping length | 12 mm |
Screw thread | M3 |
Torque | 0.5 Nm … 0.6 Nm |
Safety-related characteristic data
Stop category | 0 |
---|---|
Designation | IEC 61508 – High demand |
Safety Integrity Level (SIL) | 3 |
Designation | IEC 61508 – Low demand |
Safety Integrity Level (SIL) | 3 |
Designation | EN 50156-2 |
Safety Integrity Level (SIL) | 3 (Reference IEC 61508) |
Standards and Regulations
Designation | Air clearances and creepage distances between the power circuits |
---|---|
Standards/regulations | DIN EN 50178, EN 60079-15 |
Rated insulation voltage | 250 V AC |
Rated surge voltage/insulation | Basic insulation 4 kV between all current paths and housing |
Safe isolation, 6 kV reinforced insulation from the control circuit and confirmation current path to the enabling current path | |
Degree of pollution | 2 |
Overvoltage category | III |
Shock | 15g |
Vibration (operation) | 10 Hz … 150 Hz, 2g |
Conformance | CE-compliant |
ATEX | II 3 G Ex nA nC IIC T4 Gc |
IECEx | Ex nA nC IIC T4 Gc |
UL, USA/Canada | cULus |
Class I, Zone 2, AEx nA nC IIC T4 / Ex nA nC IIC Gc T4 X | |
Class I, Div. 2, Groups A, B, C, D, T4 | |
Environmental simulation test | ISA-S71.04 (G3) |
Environmental Product Compliance
REACh SVHC | Lead 7439-92-1 |
---|---|
China RoHS | Environmentally Friendly Use Period = 50 |
For details about hazardous substances go to tab “Downloads”, Category “Manufacturer’s declaration” |
Classifications
[email protected]
[email protected] 5.1 | 27371901 |
---|---|
[email protected] 6.0 | 27371800 |
[email protected] 7.0 | 27371819 |
[email protected] 8.0 | 27371819 |
[email protected] 9.0 | 27371819 |