TRIO-PS-IP67/1AC/24DC/20 1039830 PHOENIX CONTACT TRIO POWER primary-switched power supply in IP67 die-cast h..
TRIO-PS-IP67/1AC/24DC/20 1039830 PHOENIX CONTACT TRIO POWER primary-switched power supply in IP67 die-cast h..
TRIO POWER primary-switched power supply in IP67 die-cast housing, input: 1-phase, output: 24 V DC / 20 A
Liên hệ:
Key Commercial Data
| Orderkey | 1039830 |
|---|---|
| Packing unit | 1 |
| Catalog page | Page 264 (C-4-2019) |
| GTIN | 4055626598703 |
| Custom tariff number | 85044030 |
Ambient conditions
| Degree of protection | IP67 |
|---|---|
| Ambient temperature (operation) | -25 °C … 85 °C (Derating >60°C: 2.5 %/K) |
| Ambient temperature (start-up type tested) | -40 °C |
| Ambient temperature (storage/transport) | -40 °C … 85 °C |
| Max. permissible relative humidity (operation) | ≤ 95 % (at 25 °C, non-condensing) |
| Climatic class | 3K3 (in acc. with EN 60721) |
| Degree of pollution | 4 |
| Installation height | ≤ 4000 m (> 2000 m, Derating: 10 %/1000 m) |
Input data
| Nominal input voltage range | 100 V AC … 240 V AC |
|---|---|
| 110 V DC … 250 V DC | |
| Input voltage range | 100 V AC … 240 V AC 10 % |
| 110 V DC … 250 V DC 10 % | |
| Dielectric strength maximum | ≤ 300 V AC 15 s |
| AC frequency range | 50 Hz … 60 Hz |
| Discharge current to PE | < 3.5 mA |
| Current consumption | 5.6 A (100 V AC) |
| 2.4 A (240 V AC) | |
| Nominal power consumption | 36.8 W |
| Inrush current | typ. 20 A (at 25 °C) |
| Mains buffering time | typ. 10 ms (120 V AC) |
| typ. 15 ms (230 V AC) | |
| Input fuse | 10 A (internal (device protection)) |
| Recommended breaker for input protection | 10 A … 16 A (Characteristics B, C, D, K) |
| Type of protection | Transient surge protection |
| Protective circuit/component | Varistor |
Output data
| Nominal output voltage | 24 V DC ±1 % |
|---|---|
| Nominal output current (IN) | 20 A |
| Dynamic Boost (IDyn.Boost) | 30 A (5 s) |
| Derating | > 60 °C … 70 °C (2.5%/K) |
| Protection against overvoltage at the output (OVP) | ≤ 30 V DC |
| Control deviation | < 1 % (change in load, static 10 % … 90 %) |
| < 3 % (Dynamic load change 10 % … 90 %, 10 Hz) | |
| < 0.1 % (change in input voltage ±10 %) | |
| Residual ripple | ≤ 30 mVPP |
| Output power | 480 W |
| Typical response time | < 1 s |
| Maximum power dissipation in no-load condition | < 3 W (120 V AC) |
| < 2.5 W (230 V AC) | |
| Power loss nominal load max. | < 48 W (120 V AC) |
| < 36 W (230 V AC) |
General
| Net weight | 3.7 kg |
|---|---|
| Efficiency | 91 % (100 V AC) |
| 93 % (230 V AC) | |
| Insulation voltage input/output | 4 kV AC (type test) |
| 1.5 kV AC (routine test) | |
| Protection class | I |
| Degree of protection | IP67 |
| MTBF (IEC 61709, SN 29500) | > 1400000 h (25 °C) |
| > 800000 h (40 °C) | |
| > 400000 h (60 °C) | |
| Assembly instructions | Alignable: 20 mm horizontally, 50 mm vertically above, 100 mm vertically below |
Connection data, input
| Connection method | Circular connector |
|---|---|
| Type of locking | M12 screw locking |
| Coding | S-coded |
| Number of positions | 3 |
Connection data, output
| Connection method | Circular connector |
|---|---|
| Type of locking | M17 standard and SPEEDCON locking |
| Coding | N-coded |
| Number of positions | 4 |
Connection data for signaling
| Connection method | Circular connector |
|---|---|
| Type of locking | SPEEDCON M12 |
| Coding | A-coded |
| Number of positions | 5 |
Standards
| Standard – Electrical safety | IEC 61010-2-201 (SELV) |
|---|---|
| Standard – Safety extra-low voltage | EN 60204-1 (PELV) |
| Standard – Safe isolation | DIN VDE 0100-410 |
| Standard – Limitation of mains harmonic currents | EN 61000-3-2 |
EMC data
| Electromagnetic compatibility | Conformance with EMC Directive 2014/30/EU |
|---|---|
| Low Voltage Directive | Conformance with Low Voltage Directive 2014/35/EC |
| Conducted noise emission | EN 55016 |
| EN 61000-6-3 (Class B) | |
| Noise emission | EN 55016 |
| EN 61000-6-3 (Class B) | |
| Flicker | EN 61000-3-3 |
| Electrostatic discharge | EN 61000-4-2 |
| Contact discharge | 6 kV (Test Level 4) |
| Discharge in air | 8 kV (Test Level 4) |
| Electromagnetic HF field | EN 61000-4-3 |
| Frequency range | 80 MHz … 1 GHz |
| Test field strength | 10 V/m (Test Level 3) |
| Frequency range | 1 GHz … 2 GHz |
| Test field strength | 10 V/m (Test Level 3) |
| Frequency range | 2 GHz … 3 GHz |
| Test field strength | 10 V/m (Test Level 3) |
| Comments | Criterion A |
| Fast transients (burst) | EN 61000-4-4 |
| Input | 4 kV (Test Level 4 – asymmetrical) |
| Output | 2 kV (Test Level 3 – asymmetrical) |
| Signal | 2 kV (Test Level 2 – asymmetrical) |
| Comments | Criterion A |
| Surge voltage load (surge) | EN 61000-4-5 |
| Input | 3 kV (Test Level 3 – symmetrical) |
| 4 kV (Test Level 4 – asymmetrical) | |
| Output | 1 kV (Test Level 2 – symmetrical) |
| 2 kV (Test Level 1 – asymmetrical) | |
| Signal | 1 kV (Test Level 2 – asymmetrical) |
| Comments | Criterion B |
| Conducted interference | EN 61000-4-6 |
| Frequency range | 0.15 MHz … 80 MHz |
| Voltage | 10 V (Test Level 3) |
| Comments | Criterion A |
| Voltage dips | EN 61000-4-11 |
| Voltage | 230 V AC |
| Frequency | 50 Hz |
| Voltage dip | 70 % |
| Number of periods | 25 periods |
| Additional text | Test Level 2 |
| Comments | Criterion A |
| Voltage dip | 40 % |
| Number of periods | 10 periods |
| Additional text | Test Level 2 |
| Comments | Criterion B |
| Voltage dip | 0 % |
| Number of periods | 1 period |
| Additional text | Test Level 2 |
| Comments | Criterion B |
| Criterion A | Normal operating behavior within the specified limits. |
| Criterion B | Temporary impairment to operational behavior that is corrected by the device itself. |
| Criterion C | Temporary adverse effects on the operating behavior, which the device corrects automatically or which can be restored by actuating the operating elements. |
Classifications
Ambient conditions
| Degree of protection | IP67 |
|---|---|
| Ambient temperature (operation) | -25 °C … 85 °C (Derating >60°C: 2.5 %/K) |
| Ambient temperature (start-up type tested) | -40 °C |
| Ambient temperature (storage/transport) | -40 °C … 85 °C |
| Max. permissible relative humidity (operation) | ≤ 95 % (at 25 °C, non-condensing) |
| Climatic class | 3K3 (in acc. with EN 60721) |
| Degree of pollution | 4 |
| Installation height | ≤ 4000 m (> 2000 m, Derating: 10 %/1000 m) |
Sản phẩm tương tự
Industrial Relays
Industrial Relays
Industrial Relays
Industrial Relays
Industrial Relays
REL-MR-110DC/21-21AU/MS 1013727 PHOENIX CONTACT Single relay
Industrial Relays
Industrial Relays
Industrial Relays
