QUINT4-PS/24DC/24DC/10/SC 1046803 PHOENIX CONTACT Primary-switched QUINT DC/DC converter for DIN rail mounti..
QUINT4-PS/24DC/24DC/10/SC 1046803 PHOENIX CONTACT Primary-switched QUINT DC/DC converter for DIN rail mounti..
Primary-switched QUINT DC/DC converter for DIN rail mounting with SFB (Selective Fuse Breaking) Technology, screw connection, input: 24 V DC, output: 24 V DC / 10 A
Liên hệ:
Key Commercial Data
| Orderkey | 1046803 |
|---|---|
| Packing unit | 1 pc |
| Catalog page | Page 291 (C-4-2019) |
| GTIN | 4055626643748 |
| Weight per Piece (excluding packing) | 1,040.000 g |
| Custom tariff number | 85044030 |
| Country of origin | TH (Thailand) |
- Drawings
- Insulation electric strength
- Output data
- LED signaling
- Signal contacts – signal output Out 2 (configurable)
- Signal contacts – remote signal input (configurable)
- Signal connection data
- Life expectancy (electrolytic capacitors)
- General data
- Ambient conditions
- Conformance/approvals
- Environmental Product Compliance
Input data
| Input voltage range | 18 V DC … 32 V AC |
|---|---|
| Electric strength, max. | 35 V DC (60 s) |
| Typical current consumption | 13.8 A (24 V DC) |
| Mains buffering | typ. 11 ms (24 V DC) |
| Switch-on time | < 1 s |
| Typical response time | 300 ms (from SLEEP MODE) |
| Inrush current limitation typical | 1.5 A (after 1 ms) |
| Inrush current integral (I2t) | < 0.02 A2s |
| Input fuse | 30 A (slow-blow, internal) |
Insulation electric strength
| Insulation voltage input/output | 4 kV DC (type test) |
|---|---|
| 2 kV DC (routine test) | |
| Type test (IEC/EN 60950-1) A | 2 kV DC |
| Type test (IEC/EN 60950-1) B | 4 kV DC |
| Type test (IEC/EN 60950-1) C | 0.5 kV DC |
| Type test (IEC/EN 60950-1) D | 0.5 kV DC |
| Production test A | 2 kV DC |
| Production test B | 2 kV DC |
| Production test C | 0.5 kV DC |
| Production test D | 0.5 kV DC |
Input connection data
| Connection method | Screw connection |
|---|---|
| Conductor cross section solid | 0.2 mm² … 6 mm² |
| Conductor cross section flexible | 0.2 mm² … 6 mm² |
| Flexible conductor cross section (ferrule with plastic sleeve) | 0.2 mm² 4 mm² |
| Flexible conductor cross section flexible (ferrule, w/o plastic sleeve) | 0.2 mm² 4 mm² |
| Conductor cross section AWG | 24 … 10 |
| Stripping length | 10 mm |
Output data
| Nominal output voltage (UN) | 24 V DC |
|---|---|
| Setting range of the output voltage (USet) | 24 V DC … 29.5 V DC (> 24 V DC, constant capacity) |
| Nominal output current (IN) | 10 A |
| Static Boost (IStat.Boost) | 12.5 A |
| Dynamic Boost (IDyn.Boost) | 20 A (5 s) |
| Selective Fuse Breaking (ISFB) | 60 A (15 ms) |
| Magnetic circuit breaker tripping | A1…A6 / B2…B6 / C1…C3 / Z1…Z6 |
| System deviation, static | < 1 % (change in load, static 10 % … 90 %) |
| System deviation, dynamic | < 3 % (Dynamic load change 10 % … 90 %, 10 Hz) |
| System deviation, input voltage change | < 0.1 % (change in input voltage ±10 %) |
| Short-circuit-proof | yes |
| No-load proof | yes |
| Residual ripple | < 50 mVPP |
| Connection in parallel | Yes, for redundancy and increased capacity |
| Connection in series | yes |
| Feedback voltage resistance | ≤ 35 V DC |
| Protection against overvoltage at the output (OVP) | ≤ 32 V DC |
| Rise time | < 1 s (UOUT(10 % … 90 %)) |
Output connection data
| Connection method | Screw connection |
|---|---|
| Conductor cross section solid | 0.2 mm² … 6 mm² |
| Conductor cross section flexible | 0.2 mm² … 6 mm² |
| Flexible conductor cross section (ferrule with plastic sleeve) | 0.2 mm² 4 mm² |
| Flexible conductor cross section flexible (ferrule, w/o plastic sleeve) | 0.2 mm² 4 mm² |
| Conductor cross section AWG | 24 … 10 |
| Stripping length | 10 mm |
LED signaling
| Types of signaling | LED |
|---|---|
| Floating signal contact | |
| Active signal output Out1 (digital, configurable) | |
| Active signal output Out2 (analog, configurable) | |
| Remote contact | |
| Signal ground SGnd | |
| POut | > 100% (LED lights up yellow, output power > 240 W) |
| > 75% (LED lights up green, output power > 180 W) | |
| > 50% (LED lights up green, output power > 120 W) | |
| UOut | > 0.9 x USet(LED lights up green) |
| < 0.9 x USet(LED flashes green) | |
| UIn | > 0.8 x UInNom(LED off) |
| < 0.8 x UInNom(LED lights up yellow) |
Signal contacts – signal output Out 1 (configurable)
| Connection labeling | 3.5 + |
|---|---|
| Digital | 0 V DC |
| 24 V DC | |
| 20 mA | |
| Default | UINinput voltage OK |
| Signal option | Output voltage |
| Output current | |
| Output power | |
| Operating hours | |
| Early warning of high temperatures | |
| OVP voltage limitation active |
Signal contacts – signal output Out 2 (configurable)
| Connection labeling | 3.6 + |
|---|---|
| Digital | 0 V DC |
| 24 V DC | |
| 20 mA | |
| Default | Output power |
| Signal option | Output voltage |
| Output current | |
| Operating hours | |
| Early warning of high temperatures | |
| OVP voltage limitation active | |
| Analog | 4 mA … 20 mA ±5 % (Load ≤400 ) |
| Signal option | Output voltage |
| Output current | |
| Output power |
Signal contacts – signal output relay 13/14 (configurable)
| Connection labeling | 3.1, 3.2 |
|---|---|
| Switch contact | floating |
| Maximum contact load | 24 V DC |
| 1 A | |
| 30 V AC | |
| 0.5 A | |
| Default | Output voltage |
| Signal option | Output current |
| Output power | |
| Operating hours | |
| Early warning of high temperatures | |
| OVP voltage limitation active | |
| UINinput voltage OK |
Signal contacts – remote signal input (configurable)
| Connection labeling | 3.3 + |
|---|---|
| Function | Output power ON/OFF (remote) |
| Default | Output power ON (>40 kΩ/24 V DC/open bridge between REM and SGnd) |
Signal contacts – signal ground SGnd
| Connection labeling | 3.4 + |
|---|---|
| Function | Signal ground |
| Reference potential | to OUT1, OUT2, REM |
Signal connection data
| Connection method | Push-in connection |
|---|---|
| Conductor cross section solid | 0.2 mm² … 1 mm² |
| Conductor cross section flexible | 0.2 mm² … 1.5 mm² |
| Flexible conductor cross section (ferrule with plastic sleeve) | 0.2 mm² 0.75 mm² |
| Flexible conductor cross section flexible (ferrule, w/o plastic sleeve) | 0.2 mm² 1.5 mm² |
| Conductor cross section AWG | 24 … 16 |
| Stripping length | 8 mm |
Life expectancy (electrolytic capacitors)
| Output current | 5 A |
|---|---|
| Temperature | 40 °C |
| Time | 367721 h |
| Voltage | 24 V DC |
| Output current | 10 A |
| Temperature | 40 °C |
| Time | 183860 h |
| Voltage | 24 V DC |
| Output current | 10 A |
| Temperature | 30 °C |
| Time | 422400 h |
| Voltage | 24 V DC |
Switching frequency
| Auxiliary converter stage | 190 kHz … 220 kHz |
|---|---|
| Main converter stage | 67 kHz … 135 kHz |
General data
| Degree of protection | IP20 |
|---|---|
| Protection class | Special with SELV input and output |
| Inflammability class in acc. with UL 94 (housing / terminal blocks) | V0 |
| Side element version | Aluminum |
| Hood version | Stainless steel X6Cr17 |
| Width | 50 mm |
| Height | 130 mm |
| Depth | 125 mm |
| Width with alternative assembly | 122 mm |
| Height with alternative assembly | 130 mm |
| Depth with alternative assembly | 53 mm |
| Weight | 0.8 kg |
| Efficiency | typ. 93.3 % (24 V DC) |
Power dissipation
| Maximum power dissipation in no-load condition | < 5 W |
|---|---|
| Power dissipation SLEEP MODE | < 2 W |
| Power loss nominal load max. | < 16 W |
Ambient conditions
| Ambient temperature (operation) | -25 °C … 70 °C (> 60 °C Derating: 2.5 %/K) |
|---|---|
| Ambient temperature (start-up type tested) | -40 °C |
| Ambient temperature (storage/transport) | -40 °C … 85 °C |
| Max. permissible relative humidity (operation) | ≤ 95 % (at 25 °C, non-condensing) |
| Maximum altitude | ≤ 5000 m (> 2000 m, observe derating) |
| Vibration (operation) | 5 Hz … 100 Hz resonance search 2.3g, 90 min., resonance frequency 2.3g, 90 min. (according to DNV GL Class C) |
| Shock | 18 ms, 30g, in each space direction (according to IEC 60068-2-27) |
| Degree of pollution | 2 |
| Climatic class | 3K3 (EN 60721) |
| Overvoltage category EN 61010-1 | II |
| Overvoltage category EN 62477-1 | III |
Standards
| EMC requirements for noise immunity | EN 61000-6-1 |
|---|---|
| EN 61000-6-2 | |
| EMC requirements for noise emission | EN 61000-6-3 |
| EN 61000-6-4 | |
| EMC requirements, power plant | IEC 61850-3 |
| EN 61000-6-5 | |
| Standard designation | Electrical safety (of control and regulation devices) |
| Standards/regulations | IEC 61010-1 |
| Standard designation | Safety extra-low voltage |
| Standards/regulations | EN 61010-1 (SELV) |
| IEC 61010-2-201 (PELV) | |
| Standard designation | Explosive atmospheres |
| Standards/regulations | IEC 60079-0 |
| IEC 60079-7 | |
| IEC 60079-11 | |
| IEC 60079-15 | |
| Standard designation | Mains variation/undervoltage |
| Standards/regulations | EN 61000-4-29 |
Conformance/approvals
| Designation | UL |
|---|---|
| Identification | UL Listed UL 61010-1 |
| Designation | UL |
| Identification | UL Listed UL 61010-2-201 |
| Designation | UL |
| Identification | UL ANSI/ISA-12.12.01 Class I, Division 2, Groups A, B, C, D T4 (Hazardous Location) |
| Designation | CSA |
| Identification | CAN/CSA-C22.2 No. 61010-1-12 |
| Designation | CSA |
| Identification | CAN/CSA-IEC 61010-2-201:14 |
| Designation | SIQ |
| Identification | Type tested (type approved) |
| Designation | SIQ |
| Identification | CB scheme (IEC 61010-1, IEC 61010-2-201) |
| Designation | Shipbuilding |
| Identification | DNV GL |
| Designation | Shipbuilding |
| Identification | ABS |
| Designation | ATEX |
| Identification | II 3 G Ex ec ic nC IIC T4 Gc X |
| Designation | IECEx |
| Identification | IECEx SIQ 19.0001X |
| Ex ec ic nC IIC T4 Gc |
EMC data
| Electromagnetic compatibility | Conformance with EMC Directive 2014/30/EU |
|---|---|
| Low Voltage Directive | Conformance with Low Voltage Directive 2014/35/EC |
| Conducted noise emission | EN 55016 |
| EN 61000-6-3 (Class B) | |
| Noise emission | EN 55016 |
| EN 61000-6-3 (Class B) | |
| DNV GL conducted interference | Class B |
| Additional text | Bridge and deck area |
| DNV GL noise radiation | Class B |
| Additional text | Bridge and deck area |
| Electrostatic discharge | EN 61000-4-2 |
| Contact discharge | 8 kV (Test Level 4) |
| Discharge in air | 15 kV (Test Level 4) |
| Electromagnetic HF field | EN 61000-4-3 |
| Frequency range | 80 MHz … 1 GHz |
| Test field strength | 20 V/m (Test Level 3) |
| Frequency range | 1 GHz … 6 GHz |
| Test field strength | 10 V/m (Test Level 3) |
| Frequency range | 1 GHz … 6 GHz |
| Test field strength | 10 V/m (Test Level 3) |
| Comments | Criterion A |
| Fast transients (burst) | EN 61000-4-4 |
| Input | 2 kV (Test Level 3 – asymmetrical) |
| Output | 2 kV (Test Level 3 – asymmetrical) |
| Signal | 2 kV (Test Level 4 – asymmetrical) |
| Comments | Criterion A |
| Surge voltage load (surge) | EN 61000-4-5 |
| Input | 1 kV (Test Level 3 – symmetrical) |
| 2 kV (Test Level 3 – asymmetrical) | |
| Output | 1 kV (Test Level 3 – symmetrical) |
| 2 kV (Test Level 3 – asymmetrical) | |
| Signal | 2 kV (Test Level 3 – asymmetrical) |
| Comments | Criterion A |
| I/O/S | asymmetrical |
| Frequency range | 0.15 MHz … 80 MHz |
| Voltage | 10 V (Test Level 3) |
| Comments | Criterion A |
| Frequency | 16.7 Hz |
| 50 Hz | |
| 60 Hz | |
| Test field strength | 100 A/m |
| Additional text | 60 s |
| Comments | Criterion A |
| Frequency | 50 Hz |
| 60 Hz | |
| Test field strength | 1 kA/m |
| Additional text | 3 s |
| Comments | Criterion A |
| Frequency | 0 Hz |
| Test field strength | 300 A/m |
| Additional text | DC, 60 s |
| Comments | Criterion A |
| Voltage dips | EN 61000-4-29 |
| Voltage | 24 V DC |
| Voltage dip | 70 % |
| Additional text | Test Level 2 |
| Comments | Criterion A |
| Voltage dip | 40 % |
| Additional text | Test Level 2 |
| Comments | Criterion B |
| Voltage dip | 0 % |
| Additional text | Test Level 2 |
| Comments | Criterion B |
| Pulse-shape magnetic field | EN 61000-4-9 |
| Test field strength | 1000 A/m |
| Comments | Criterion A |
| Damped oscillating magnetic field | EN 61000-4-10 |
| Test field strength | 100 A/m |
| Test level 1 | 100 kHz |
| Test field strength | 100 A/m |
| Test level 2 | 1 MHz |
| Comments | Criterion A |
| Asymmetrical conducted disturbance variables | EN 61000-4-16 |
| Test level 1 | 15 Hz 150 Hz (Test Level 3) |
| Voltage | 10 V 1 V |
| Test level 2 | 150 Hz 1.5 kHz (Test Level 3) |
| Voltage | 1 V |
| Test level 3 | 1.5 kHz 15 kHz (Test Level 3) |
| Voltage | 1 V 10 V |
| Test level 4 | 15 kHz 150 kHz (Test Level 3) |
| Voltage | 10 V |
| Test level 5 | 16.7 Hz 50 Hz 60 Hz 150 Hz 180 Hz (Test Level 3) |
| Voltage | 10 V (Permanent) |
| Test level 6 | 0 Hz 16.7 Hz 50 Hz 60 Hz (Test Level 3) |
| Voltage | 100 V (1 s) |
| Comments | Criterion A |
| Alternating component of DC voltage | EN 61000-4-17 |
| Attenuated oscillating wave | EN 61000-4-18 |
| Input, output (test level 1) | 100 kHz 1 MHz (Test Level 2 – symmetrical) |
| Voltage | 0.5 kV |
| Input, output (test level 2) | 100 kHz 1 MHz (Test Level 2 – asymmetrical) |
| Voltage | 1 kV |
| Input, output (test level 1) | 10 MHz (Test Level 2 – asymmetrical) |
| Voltage | 0.5 kV |
| Signals (test level 1) | 100 kHz 1 MHz (Test Level 2 – symmetrical) |
| Voltage | 0.5 kV |
| Signals (test level 2) | 100 kHz 1 MHz (Test Level 2 – asymmetrical) |
| Voltage | 1 kV |
| Comments | Criterion A |
| Criterion A | Normal operating behavior within the specified limits. |
| Criterion B | Temporary impairment to operational behavior that is corrected by the device itself. |
| Criterion C | Temporary adverse effects on the operating behavior, which the device corrects automatically or which can be restored by actuating the operating elements. |
Classifications
- Drawings
- Insulation electric strength
- Output data
- LED signaling
- Signal contacts – signal output Out 2 (configurable)
- Signal contacts – remote signal input (configurable)
- Signal connection data
- Life expectancy (electrolytic capacitors)
- General data
- Ambient conditions
- Conformance/approvals
- Environmental Product Compliance
Insulation electric strength
| Insulation voltage input/output | 4 kV DC (type test) |
|---|---|
| 2 kV DC (routine test) | |
| Type test (IEC/EN 60950-1) A | 2 kV DC |
| Type test (IEC/EN 60950-1) B | 4 kV DC |
| Type test (IEC/EN 60950-1) C | 0.5 kV DC |
| Type test (IEC/EN 60950-1) D | 0.5 kV DC |
| Production test A | 2 kV DC |
| Production test B | 2 kV DC |
| Production test C | 0.5 kV DC |
| Production test D | 0.5 kV DC |
Sản phẩm tương tự
Industrial Relays
Industrial Relays
Industrial Relays
Industrial Relays
Industrial Relays
Industrial Relays
Industrial Relays
