QUINT4-PS/24DC/24DC/10/PT 2910120 PHOENIX CONTACT Primary-switched QUINT DC/DC converter for DIN rail mounti..

Primary-switched QUINT DC/DC converter for DIN rail mounting with SFB (Selective Fuse Breaking) Technology, Push-in connection, input: 24 V DC, output: 24 V DC / 10 A

sản phẩm chính hãng, MỚI 100% CHƯA SỬ DỤNG
SẢN PHẨM LUÔN ĐƯỢC KIỂM TRA TRƯỚC KHI XUẤT KHO
BẢO HÀNH 12 THÁNG ĐỐI VỚI LỖI CỦA NHÀ SẢN XUẤT / HOẶC THEO CHÍNH SÁCH CỦA SẢN PHẨM DO TRƯỜNG THỊNH PHÂN PHỐI
HỖ TRỢ KỸ THUẬT 24/7
MIỄN PHÍ GIAO HÀNG ĐỐI VỚI CÁC ĐƠN HÀNG TỪ 8,000,000VNĐ

Liên hệ:

Mô tả

Key Commercial Data

Orderkey	2910120
Packing unit	1 pc
Catalog page	Page 289 (C-4-2019)
GTIN	4055626537498
Weight per Piece (excluding packing)	1,040.000 g
Custom tariff number	85044030
Country of origin	TH (Thailand)

Drawings
Insulation electric strength
Output data
LED signaling
Signal contacts – signal output Out 2 (configurable)
Signal contacts – remote signal input (configurable)
Signal connection data
Life expectancy (electrolytic capacitors)
General data
Ambient conditions
Conformance/approvals
Classifications

Input data
Input connection data
Output connection data
Signal contacts – signal output Out 1 (configurable)
Signal contacts – signal output relay 13/14 (configurable)
Signal contacts – signal ground SGnd
Reliability
Switching frequency
Power dissipation
Standards
EMC data

Drawings


Block diagram		Diagram

Diagram		Diagram

Schematic diagram

Input data

Input voltage range	24 V DC -25 % … +40 %
Electric strength, max.	35 V DC (60 s)
Typical current consumption	13.8 A (24 V DC)
Mains buffering	typ. 11 ms (24 V DC)
Switch-on time	< 1 s
Typical response time	300 ms (from SLEEP MODE)
Inrush current limitation typical	1.5 A (after 1 ms)
Inrush current integral (I²t)	< 0.02 A²s
Input fuse	30 A (slow-blow, internal)

Insulation electric strength

Insulation voltage input/output	4 kV DC (type test)
	2 kV DC (routine test)
Type test (IEC/EN 60950-1) A	2 kV DC
Type test (IEC/EN 60950-1) B	4 kV DC
Type test (IEC/EN 60950-1) C	0.5 kV DC
Type test (IEC/EN 60950-1) D	0.5 kV DC
Production test A	2 kV DC
Production test B	2 kV DC
Production test C	0.5 kV DC
Production test D	0.5 kV DC

Input connection data

Connection method	Push-in connection
Conductor cross section solid	0.2 mm² … 6 mm²
Conductor cross section flexible	0.2 mm² … 6 mm²
Flexible conductor cross section (ferrule with plastic sleeve)	0.2 mm² 4 mm²
Flexible conductor cross section flexible (ferrule, w/o plastic sleeve)	0.2 mm² 4 mm²
Conductor cross section AWG	24 … 10
Stripping length	10 mm

Output data

Nominal output voltage (U_N)	24 V DC
Setting range of the output voltage (U_Set)	24 V DC … 29.5 V DC (> 24 V DC, constant capacity)
Nominal output current (I_N)	10 A
Static Boost (I_Stat.Boost)	12.5 A
Dynamic Boost (I_Dyn.Boost)	20 A (5 s)
Selective Fuse Breaking (I_SFB)	60 A (15 ms)
Magnetic circuit breaker tripping	A1…A6 / B2…B6 / C1…C3 / Z1…Z6
System deviation, static	< 1 % (change in load, static 10 % … 90 %)
System deviation, dynamic	< 3 % (Dynamic load change 10 % … 90 %, 10 Hz)
System deviation, input voltage change	< 0.1 % (change in input voltage ±10 %)
Short-circuit-proof	yes
No-load proof	yes
Residual ripple	< 50 mV_PP
Connection in parallel	Yes, for redundancy and increased capacity
Connection in series	yes
Feedback voltage resistance	≤ 35 V DC
Protection against overvoltage at the output (OVP)	≤ 32 V DC
Rise time	< 1 s (U_OUT(10 % … 90 %))

Output connection data

Connection method	Push-in connection
Conductor cross section solid	0.2 mm² … 6 mm²
Conductor cross section flexible	0.2 mm² … 6 mm²
Flexible conductor cross section (ferrule with plastic sleeve)	0.2 mm² 4 mm²
Flexible conductor cross section flexible (ferrule, w/o plastic sleeve)	0.2 mm² 4 mm²
Conductor cross section AWG	24 … 10
Stripping length	10 mm

LED signaling

Types of signaling	LED
	Floating signal contact
	Active signal output Out1 (digital, configurable)
	Active signal output Out2 (analog, configurable)
	Remote contact
	Signal ground SGnd
P_Out	> 100% (LED lights up yellow, output power > 240 W)
	> 75% (LED lights up green, output power > 180 W)
	> 50% (LED lights up green, output power > 120 W)
U_Out	> 0.9 x U_Set(LED lights up green)
	< 0.9 x U_Set(LED flashes green)
U_In	> 0.8 x U_InNom(LED off)
	< 0.8 x U_InNom(LED lights up yellow)

Signal contacts – signal output Out 1 (configurable)

Connection labeling	3.5 +
Digital	0 V DC
	24 V DC
	20 mA
Default	U_INinput voltage OK
Signal option	Output voltage
	Output current
	Output power
	Operating hours
	Early warning of high temperatures
	OVP voltage limitation active

Signal contacts – signal output Out 2 (configurable)

Connection labeling	3.6 +
Digital	0 V DC
	24 V DC
	20 mA
Default	Output power
Signal option	Output voltage
	Output current
	Operating hours
	Early warning of high temperatures
	OVP voltage limitation active
Analog	4 mA … 20 mA ±5 % (Load ≤400 )
Signal option	Output voltage
	Output current
	Output power

Signal contacts – signal output relay 13/14 (configurable)

Connection labeling	3.1, 3.2
Switch contact	floating
Maximum contact load	24 V DC
	1 A
	30 V AC
	0.5 A
Default	Output voltage
Signal option	Output current
	Output power
	Operating hours
	Early warning of high temperatures
	OVP voltage limitation active
	U_INinput voltage OK

Signal contacts – remote signal input (configurable)

Connection labeling	3.3 +
Function	Output power ON/OFF (remote)
Default	Output power ON (>40 kΩ/24 V DC/open bridge between REM and SGnd)

Signal contacts – signal ground SGnd

Connection labeling	3.4 +
Function	Signal ground
Reference potential	to OUT1, OUT2, REM

Signal connection data

Connection method	Push-in connection
Conductor cross section solid	0.2 mm² … 1 mm²
Conductor cross section flexible	0.2 mm² … 1.5 mm²
Flexible conductor cross section (ferrule with plastic sleeve)	0.2 mm² 0.75 mm²
Flexible conductor cross section flexible (ferrule, w/o plastic sleeve)	0.2 mm² 1.5 mm²
Conductor cross section AWG	24 … 16
Stripping length	8 mm

Reliability

MTBF (IEC 61709, SN 29500)	> 1380000 h (25 °C)
	> 800000 h (40 °C)
	> 340000 h (60 °C)

Life expectancy (electrolytic capacitors)

Output current	5 A
Temperature	40 °C
Time	367721 h
Voltage	24 V DC
Output current	10 A
Temperature	40 °C
Time	183860 h
Voltage	24 V DC
Output current	10 A
Temperature	30 °C
Time	422400 h
Voltage	24 V DC

Switching frequency

Auxiliary converter stage	190 kHz … 220 kHz
Main converter stage	67 kHz … 135 kHz

General data

Degree of protection	IP20
Protection class	Special with SELV input and output
Inflammability class in acc. with UL 94 (housing / terminal blocks)	V0
Side element version	Aluminum
Hood version	Stainless steel X6Cr17
Width	50 mm
Height	130 mm
Depth	125 mm
Width with alternative assembly	122 mm
Height with alternative assembly	130 mm
Depth with alternative assembly	53 mm
Weight	0.8 kg
Efficiency	typ. 93.3 % (24 V DC)

Power dissipation

Maximum power dissipation in no-load condition	< 5 W
Power dissipation SLEEP MODE	< 2 W
Power loss nominal load max.	< 16 W

Ambient conditions

Ambient temperature (operation)	-25 °C … 70 °C (> 60 °C Derating: 2.5 %/K)
Ambient temperature (start-up type tested)	-40 °C
Ambient temperature (storage/transport)	-40 °C … 85 °C
Max. permissible relative humidity (operation)	≤ 95 % (at 25 °C, non-condensing)
Maximum altitude	≤ 5000 mm (> 2000 m, observe derating)
Vibration (operation)	5 Hz … 100 Hz resonance search 2.3g, 90 min., resonance frequency 2.3g, 90 min. (according to DNV GL Class C)
Shock	18 ms, 30g, in each space direction (according to IEC 60068-2-27)
Degree of pollution	2
Climatic class	3K3 (EN 60721)
Overvoltage category EN 61010-1	II
Overvoltage category EN 62477-1	III

Standards

EMC requirements for noise immunity	EN 61000-6-1
	EN 61000-6-2
EMC requirements for noise emission	EN 61000-6-3
	EN 61000-6-4
EMC requirements, power plant	IEC 61850-3
	EN 61000-6-5
Standard designation	Electrical safety (of control and regulation devices)
Standards/regulations	IEC 61010-1
Standard designation	Safety extra-low voltage
Standards/regulations	EN 61010-1 (SELV)
	IEC 61010-2-201 (PELV)
Standard designation	Explosive atmospheres
Standards/regulations	IEC 60079-0
	IEC 60079-7
	IEC 60079-11
	IEC 60079-15
Standard designation	Mains variation/undervoltage
Standards/regulations	EN 61000-4-29

Conformance/approvals

Designation	UL
Identification	UL Listed UL 61010-1
Designation	UL
Identification	UL Listed UL 61010-2-201
Designation	UL
Identification	UL ANSI/ISA-12.12.01 Class I, Division 2, Groups A, B, C, D T4 (Hazardous Location)
Designation	CSA
Identification	CAN/CSA-C22.2 No. 61010-1-12
Designation	CSA
Identification	CAN/CSA-IEC 61010-2-201:14
Designation	SIQ
Identification	Type tested (type approved)
Designation	SIQ
Identification	CB scheme (IEC 61010-1, IEC 61010-2-201)
Designation	Shipbuilding
Identification	DNV GL
Designation	Shipbuilding
Identification	ABS
Designation	ATEX
Identification	 II 3 G Ex ec ic nC IIC T4 Gc X
Designation	IECEx
Identification	IECEx SIQ 19.0001X
	Ex ec ic nC IIC T4 Gc

EMC data

Electromagnetic compatibility	Conformance with EMC Directive 2014/30/EU
Low Voltage Directive	Conformance with Low Voltage Directive 2014/35/EC
Conducted noise emission	EN 55016
	EN 61000-6-3 (Class B)
Noise emission	EN 55016
	EN 61000-6-3 (Class B)
DNV GL conducted interference	Class B
Additional text	Bridge and deck area
DNV GL noise radiation	Class B
Additional text	Bridge and deck area
Electrostatic discharge	EN 61000-4-2
Contact discharge	8 kV (Test Level 4)
Discharge in air	15 kV (Test Level 4)
Electromagnetic HF field	EN 61000-4-3
Frequency range	80 MHz … 1 GHz
Test field strength	20 V/m (Test Level 3)
Frequency range	1 GHz … 6 GHz
Test field strength	10 V/m (Test Level 3)
Frequency range	1 GHz … 6 GHz
Test field strength	10 V/m (Test Level 3)
Comments	Criterion A
Fast transients (burst)	EN 61000-4-4
Input	2 kV (Test Level 3 – asymmetrical)
Output	2 kV (Test Level 3 – asymmetrical)
Signal	2 kV (Test Level 4 – asymmetrical)
Comments	Criterion A
Surge voltage load (surge)	EN 61000-4-5
Input	1 kV (Test Level 3 – symmetrical)
	2 kV (Test Level 3 – asymmetrical)
Output	1 kV (Test Level 3 – symmetrical)
	2 kV (Test Level 3 – asymmetrical)
Signal	2 kV (Test Level 3 – asymmetrical)
Comments	Criterion A
I/O/S	asymmetrical
Frequency range	0.15 MHz … 80 MHz
Voltage	10 V (Test Level 3)
Comments	Criterion A
Frequency	16.7 Hz
	50 Hz
	60 Hz
Test field strength	100 A/m
Additional text	60 s
Comments	Criterion A
Frequency	50 Hz
	60 Hz
Test field strength	1 kA/m
Additional text	3 s
Comments	Criterion A
Frequency	0 Hz
Test field strength	300 A/m
Additional text	DC, 60 s
Comments	Criterion A
Voltage dips	EN 61000-4-29
Voltage	24 V DC
Voltage dip	70 %
Additional text	Test Level 2
Comments	Criterion A
Voltage dip	40 %
Additional text	Test Level 2
Comments	Criterion B
Voltage dip	0 %
Additional text	Test Level 2
Comments	Criterion B
Pulse-shape magnetic field	EN 61000-4-9
Test field strength	1000 A/m
Comments	Criterion A
Damped oscillating magnetic field	EN 61000-4-10
Test field strength	100 A/m
Test level 1	100 kHz
Test field strength	100 A/m
Test level 2	1 MHz
Comments	Criterion A
Asymmetrical conducted disturbance variables	EN 61000-4-16
Test level 1	15 Hz 150 Hz (Test Level 3)
Voltage	10 V 1 V
Test level 2	150 Hz 1.5 kHz (Test Level 3)
Voltage	1 V
Test level 3	1.5 kHz 15 kHz (Test Level 3)
Voltage	1 V 10 V
Test level 4	15 kHz 150 kHz (Test Level 3)
Voltage	10 V
Test level 5	16.7 Hz 50 Hz 60 Hz 150 Hz 180 Hz (Test Level 3)
Voltage	10 V (Permanent)
Test level 6	0 Hz 16.7 Hz 50 Hz 60 Hz (Test Level 3)
Voltage	100 V (1 s)
Comments	Criterion A
Alternating component of DC voltage	EN 61000-4-17
Attenuated oscillating wave	EN 61000-4-18
Input, output (test level 1)	100 kHz 1 MHz (Test Level 2 – symmetrical)
Voltage	0.5 kV
Input, output (test level 2)	100 kHz 1 MHz (Test Level 2 – asymmetrical)
Voltage	1 kV
Input, output (test level 1)	10 MHz (Test Level 2 – asymmetrical)
Voltage	0.5 kV
Signals (test level 1)	100 kHz 1 MHz (Test Level 2 – symmetrical)
Voltage	0.5 kV
Signals (test level 2)	100 kHz 1 MHz (Test Level 2 – asymmetrical)
Voltage	1 kV
Comments	Criterion A
Criterion A	Normal operating behavior within the specified limits.
Criterion B	Temporary impairment to operational behavior that is corrected by the device itself.
Criterion C	Temporary adverse effects on the operating behavior, which the device corrects automatically or which can be restored by actuating the operating elements.

Classifications

[email protected]

[email protected] 8.0	27210901
[email protected] 9.0	27210901

ETIM

ETIM 5.0	EC002046
ETIM 6.0	EC002046
ETIM 7.0	EC002046

Drawings
Insulation electric strength
Output data
LED signaling
Signal contacts – signal output Out 2 (configurable)
Signal contacts – remote signal input (configurable)
Signal connection data
Life expectancy (electrolytic capacitors)
General data
Ambient conditions
Conformance/approvals
Classifications

Input data
Input connection data
Output connection data
Signal contacts – signal output Out 1 (configurable)
Signal contacts – signal output relay 13/14 (configurable)
Signal contacts – signal ground SGnd
Reliability
Switching frequency
Power dissipation
Standards
EMC data

Drawings


Block diagram		Diagram

Diagram		Diagram

Schematic diagram

Insulation electric strength

Insulation voltage input/output	4 kV DC (type test)
	2 kV DC (routine test)
Type test (IEC/EN 60950-1) A	2 kV DC
Type test (IEC/EN 60950-1) B	4 kV DC
Type test (IEC/EN 60950-1) C	0.5 kV DC
Type test (IEC/EN 60950-1) D	0.5 kV DC
Production test A	2 kV DC
Production test B	2 kV DC
Production test C	0.5 kV DC
Production test D	0.5 kV DC

MÁY IN CÔNG NGHIỆP

MÁY SẢN XUẤT KHÍ NI-TƠ

MÁY ĐÓNG GÓI

DỊCH VỤ TƯ VẤN

Dịch vụ tư vấn - Khảo sát miễn phí duy nhất tại Trường Thịnh Tech

thi công lắp đặt

Trường Thịnh Tech cung cấp và lắp đặt hoàn thiện dự án

bảo dưỡng định kỳ

Bảo hành - bảo dưỡng với các sản phẩm, dịch vụ do Trường Thịnh Tech cấp ra

THIẾT BỊ

Trường Thịnh cung cấp thiết bị và máy móc trọn gói, đúng chuẩn cho Quý doanh nghiệp

QUINT4-PS/24DC/24DC/10/PT 2910120 PHOENIX CONTACT Primary-switched QUINT DC/DC converter for DIN rail mounti..

sản phẩm chính hãng, MỚI 100% CHƯA SỬ DỤNG

SẢN PHẨM LUÔN ĐƯỢC KIỂM TRA TRƯỚC KHI XUẤT KHO

BẢO HÀNH 12 THÁNG ĐỐI VỚI LỖI CỦA NHÀ SẢN XUẤT / HOẶC THEO CHÍNH SÁCH CỦA SẢN PHẨM DO TRƯỜNG THỊNH PHÂN PHỐI

HỖ TRỢ KỸ THUẬT 24/7

MIỄN PHÍ GIAO HÀNG ĐỐI VỚI CÁC ĐƠN HÀNG TỪ 8,000,000VNĐ

Liên hệ:

Key Commercial Data

Drawings

Input data

Insulation electric strength

Input connection data

Output data

Output connection data

LED signaling

Signal contacts – signal output Out 1 (configurable)

Signal contacts – signal output Out 2 (configurable)

Signal contacts – signal output relay 13/14 (configurable)

Signal contacts – remote signal input (configurable)

Signal contacts – signal ground SGnd

Signal connection data

Reliability

Life expectancy (electrolytic capacitors)

Switching frequency

General data

Power dissipation

Ambient conditions

Standards

Conformance/approvals

EMC data

Classifications

[email protected]

ETIM

Drawings

Insulation electric strength

Sản phẩm tương tự

Đăng nhập